三工位母線加工機減小誤差方法——力建數控

發布日期：2019-04-15 作者：力建數控點擊：

來源：力建數控母線機、母線加工機、銅排加工機、母排加工機生產廠家責任編輯：01顧問

三工位母線加工機在實現沖孔、切斷和折彎操作時，誤差難以避免。為了提高加工精度，對于誤差，采取盡量減小的措施。下面小編為大家介紹一下母線加工機誤差減小的方法：

1、三工位母線加工機重復定位精度的影響：母線加工機的定位精度是指數控三工位母線加工機各坐標軸在系統的控制下運動的位置精度，引起定位誤差的因素包括系統的誤差和機械傳動的誤差。而系統的誤差則與插補誤差、跟蹤誤差等有關。三工位母線加工機機重復定位精度是指重復定位時坐標軸的實際位置和理想位置的符合程度。

2、三工位母線加工機刀具誤差的影響：在加工中心上，由于采用的刀具具有自動交換功能，因而在提高生產率的同時，也帶來了刀具交換誤差。用同一把刀具加工一批工件時，由于頻繁重復換刀，致使刀柄相對于主軸錐孔產生重復定位誤差而降低加工精度。

3、三工位母線加工機檢測裝置的影響：檢測反饋裝置也稱為反饋元件，通常安裝在三工位母線加工機工作臺或絲杠上，檢測反饋裝置將工作臺位移量轉換成電信號，并且反饋給數控裝置，如果與指令值比較有誤差，則控制工作臺向消除誤差的方向移動。數控系統按有無檢測裝置可分為開環、閉環與半閉環系統。開環系統精度取決于步進電動機和絲杠精度，閉環系統精度取決于檢測裝置精度。檢測裝置是高性能母線加工機的重要組成部分。

三工位母線加工機減小誤差方法——力建數控

如果您對以上數控母線加工機、數控母排加工機、數控銅排加工機感興趣或有疑問,請點擊官網或aptengmeisiwang.com在線客服,或致電：0531-87512217，力建數控——創新發展、專業生產、專注母線加工機設備十余年。