數控母排加工機銅排加工機剪切、沖孔開機過程-力建數控

發布日期：2018-04-17 作者：力建數控點擊：

來源：力建數控母線機、母線加工機、銅排加工機、母排加工機生產廠家責任編輯：01顧問

首先數控母排加工機銅排加工機應該打開電源開關。踏一下腳踏開關，該單元油泵啟動，再踩下沖孔單元腳踏開關，沖孔將前進，前進過程松開腳踏開關，沖頭停止運行，再次踩下腳踏開關，沖頭將繼續前進，當接近限位開關時，數控母排加工機銅排加工機沖頭將自動返回上止點。過程，需要數控母排加工機銅排加工機沖頭返回時，按下數控母排加工機銅排加工機相應的手動后退按鈕，沖頭將退回，松開后退按鈕，沖頭則停止后退。

一、數控母排加工機銅排加工機剪切、班前給個運動部位涂潤滑油上下午各一次。利用數控母排加工機銅排加工機上下刀塊的觀察孔觀察實際剪切位置。利用標尺滑塊擋料，放置母線排在工作臺上。確定剪切尺寸，然后用壓料手輪將母線壓好，防止資料翹起，損壞模具。

二、沖孔、班前給數控母排加工機銅排加工機每個運動部位涂潤滑油上下午各一次。沖孔加工中應確保加工資料堅持水平。必需選用配套模具，數控母排加工機銅排加工機進行沖孔加工時切記不要將不同內徑的上下模具混裝，數控母排加工機銅排加工機加工沖孔時一定要使上下模方向一致，否則將損壞模具。

數控母排加工機銅排加工機剪切、沖孔開機過程-力建數控

如果您對以上數控母線加工機、數控母排加工機、數控銅排加工機感興趣或有疑問,請點擊官網或aptengmeisiwang.com在線客服,或致電：0531-87512217，力建數控——創新發展、專業生產、專注母線加工機設備十余年。