數控母排加工機銅排加工機的操作方法-力建數控

發布日期：2018-04-21 作者：力建數控 點擊：

來源：力建數控母線機、母線加工機、銅排加工機、母排加工機生產廠家責任編輯：01顧問

為提高工作效率及保證作業安全之要求而設計的配套設備--數控母排加工機銅排加工機,數控母排加工機銅排加工機最適合制作大型的電控箱及輸配電建設工程的施工現場使用.下面小編就為大家介紹一下數控母排加工機銅排加工機簡單的操作方法：

數控母排加工機銅排加工機使用前應檢查插頭及電源線是否正常,接通電源,打開電源開關(綠色開/紅色關),正常工作時無需關閉開關,不工作時請切斷電源.

在沖孔和切排時可根據機組工作臺面上的限位裝置進行操作,數控母排加工機銅排加工機您可調好限位裝置,然后工件靠在限位裝置上,確保工作沖孔或切排尺寸.

當您在使用數控母排加工機銅排加工機沖孔時,請將換向手柄打至標有沖孔字樣的位置;在使用沖孔完成后,把手柄打至回油標貼位置即可.

當您在使用數控母排加工機銅排加工機切排時,請將換向手柄打至標有切排字樣的位置;在使用切排完成后,把手柄打至回油標貼位置即可.

當您在使用數控母排加工機銅排加工機彎排時,請將換向手柄打至標有彎排字樣的位置;在使用彎排完成后,把手柄打至回油標貼位置即可.

數控母排加工機銅排加工機的操作方法-力建數控

如果您對以上數控母線加工機、數控母排加工機、數控銅排加工機感興趣或有疑問,請點擊官網或aptengmeisiwang.com在線客服,或致電：0531-87512217，力建數控——創新發展、專業生產、專注母線加工機設備十余年。