數控母線加工機銅排加工機液壓泵站使用和維護

發布日期：2018-06-21 作者：力建數控點擊：

來源：力建數控母線機、母線加工機、銅排加工機、母排加工機生產廠家責任編輯：01顧問

　　關于數控母線加工機銅排加工機，大家都不陌生了，在社會的發展和進步中，數控母線加工機銅排加工機以自身的優勢在不同的應用中做出了很大的貢獻，下面給大家介紹一下母線加工機的液壓泵站使用和維護.

　　數控母線加工機銅排加工機油泵使用46#機械油,泵站啟動時,必須把卸荷閥打開,以防電機過載.

　　各閥出廠前均已調試到額(e)定壓力,一般情況下對各閥不得隨便調整,長期在低于額(e)定壓力的情況下使用,可將高壓安全閥工作壓力調低,高壓安全閥調壓時拆去保護帽,用螺絲刀逆時針擰動螺釘即可降低壓力,反之則壓力長高,但切不可將壓力調至高于該泵的額(e)定壓力.

　　數控母線加工機銅排加工機雙作用泵,連接 配套油缸A出口為工作高壓,B出口為回位低壓,不可連接反向.該泵正常工作溫度-20℃-55℃,溫度過高應進行冷卻或停泵,油溫過低不允許泵直接工作需采取加溫措施,需間接加溫切不可用火直接加溫.

　　高壓膠管應隨時檢查,以防出現事故,一般半年應進行一次膠管壓力試驗,試驗壓力應大于87Kgf/㎡,高壓膠管在使用過程中應避免打折和急彎,操作者不可靠膠管太近,以防意外.

　　該泵每年應進行一次檢修,各件用輕柴油或煤油清洗并注意保護配合面.電動泵站接線時,一定要接上地線,以防發生觸電事故.應保持油箱的油量在貯油的四分之三以上,加油時應用120-160目的濾油網過濾,一般應兩個月清洗一次數控母線加工機銅排加工機,更換新油液.

數控母線加工機銅排加工機液壓泵站使用和維護

如果您對以上數控母線加工機、數控母排加工機、數控銅排加工機感興趣或有疑問,請點擊官網或aptengmeisiwang.com在線客服,或致電：0531-87512217，力建數控——創新發展、專業生產、專注母線加工機設備十余年。