數控母線加工機銅排加工機更換配件時的注意事項-力建數控

發布日期：2018-04-28 作者：力建數控 點擊：

來源：力建數控母線機、母線加工機、銅排加工機、母排加工機生產廠家責任編輯：01顧問

當數控母線加工機銅排加工機的故障分析結果集中于某一控制電路板上時,由于電路集成度的不斷擴大而要把故障落實于其上某一區域乃至某一元件是十分困難的,為了縮短停機時間,在有相同備件的條件下可以先將備件換上,然后再去檢查修復故障板.備件板的更換要注意以下問題.

　　更換任何的數控母線加工機銅排加工機配件時都必須在斷電情況下進行.許多母數控母線加工機銅排加工機控制電路板上都有一些開關或短路棒的設定以匹配實際需要,因此在更換備件板上一定要記錄下原有的開關位置和設定狀態,并將數控母線加工機銅排加工機新板作好同樣的設定,否則會產生報警而不能工作.某些印制電路板的更換還需在更換后進行某些特定操作以完成其中軟件與參數的建立.

　　在數控母線加工機銅排加工機中,有些控制電路板是不能輕易拔出的,例如含有工作存儲器的板,或者備用電池板,它會丟失有用的參數或者程序.必須更換時也必須遵照有關說明操作.鑒于以上條件,在拔出數控母線加工機銅排加工機舊板更換新板之前一定要先仔細閱讀相關資料,弄懂要求和操作步驟之后再動手,以免造成更大的故障.

數控母線加工機銅排加工機更換配件時的注意事項-力建數控

如果您對以上數控母線加工機、數控母排加工機、數控銅排加工機感興趣或有疑問,請點擊官網或aptengmeisiwang.com在線客服,或致電：0531-87512217，力建數控——創新發展、專業生產、專注母線加工機設備十余年。